How to Replace a Kia Sportage Replacement Key
For many Kia models the key comes with the keyless entry system that is built into the key. This key usually resembles the remote control and can be changed with a new one from a Kia dealer or a locksmith.
Key fobs can stop working due to a number of reasons, such as the battery being dead, worn-out buttons, signal interference or water damage. Here are some helpful tips to help you get your Kia key fob that is a replacement for the sportage again.
How to replace the remote key or smart key?
It doesn't matter if your Kia is equipped with an intelligent key, remote key push to start key or a regular non-transponder steel key, the battery in these keys will eventually require replacement. This is especially relevant if your vehicle displays a message that indicates that the smart key or remote is not powered by the battery.
This is a relatively easy procedure. In order to replace the battery of the key fob take the mechanical key from the slit in the back of the key fob and break the cover. A small screw is inside the key fob that holds the battery in place. With a small screwdriver, unscrew the screw and remove the battery that was in place. Insert the new battery and then close the opening on the key fob.
Once the key fob has a fresh battery check it by pressing the lock and unlock buttons. You're good to go if the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or when you need to do some errands in Brandon.
Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a programming machine which is available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming. If your key needs to be programmed again, you must be aware of the key code number stamped on the tag that identifies the key and then record the number in a secure place.
How do you replace the battery?
If the Kia key fob is unable to respond when you press the lock/unlock button, it is most likely that the battery is depleted. A battery that is not functioning properly can cause other issues, such as the check engine light flashing or the engine not working properly. It is relatively easy to replace key fob battery with just the use of a few tools.
Make sure that you shut off your vehicle and close the doors before you begin. Find the small metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the metal key is released. The key can be placed inside the driver door handle to unlock your car.
To replace replacement key for kia picanto , take off the cover on the rear and use a pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and then position the new battery to ensure that its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.
After the new battery has been installed then turn the key fob off and then turn it on in the ignition until the door locks. You can then test the Kia's key fob again to make sure it's working as intended.
How can you replace the smart key
You can have a standard keyfob or a Smart Key, based on the model of Kia Sportage. The smart key has an embedded mechanical key blade, however, the standard key fob does not. Both key fobs come with an internal battery that will eventually require replacing. It's a fairly simple process that will take about two minutes.
Before you begin it is essential to ensure that you're on a flat surface with sufficient lighting and that your Kia is turned off. Be aware that there are small parts inside the fob that could be removed if not cautious.
The first step is to find the small release button on the backside of the fob. It will be a circular button or rectangular slot. You can open the key fob by pressing the button.
Once the key fob is open, remove the old battery. The new battery is one called CR-2032 and can be bought online or in your local auto parts store. When you're done, the key fob should be able to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.
How to replace a mechanical key
The Kia key fob is a great option that lets us lock and unlock our vehicle with the push of an button. However, like all devices it may have issues at times. Luckily, there are ways to solve these issues and ensure that our key fobs are in good condition for the long run.
One of the most frequent problems is a dead or dead battery. The battery could cause the device to stop working or operate intermittently. If this is the problem it is time to replace the battery an entirely new battery.
If this doesn't solve the problem Try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage internal components or scratch the plastic. After the battery has been removed then replace it with a brand new one.
Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to verify that it's working properly. If the key fob isn't functioning, contact a locksmith or dealer to help solve the issue. Make sure they make you an emergency key that can work for all trunk and door cylinders to avoid lockouts again.